Installing an invisible zipper
in your project is a simple way to get a professional finish, but what if you could make the zipper seam disappear, too? Take a few simple steps to match the pattern across your zipper opening and it becomes almost invisible as well. It's easier than you think!
Follow these simple steps (and grab your glue stick!) to get a perfect pattern match across your zipper opening.
The thought of using a regular school glue stick to baste fabric might surprise you, but it is one of my most-used sewing tools
! The best glue stick I have found is Elmer's X-treme School Glue Stick. A regular strength glue stick works well too, though the bond is not as strong. As long as the glue is applied with a thin, even stroke and is fully dry before sewing, it does not leave residue on your machine needle.
I am using a simple sleeveless bodice with a center-back zipper in this tutorial. You can also use this tutorial to match fabric across any straight zipper opening. It could be on a skirt, dress back, side zipper or even a throw pillow cover.
Preparing your fabric
This tutorial augments the instructions you have in your sewing pattern. You may need extra yardage to match your fabric. You can also find a general tutorial on how to install an invisible zipper in the Bluprint blog post “Sewing an Invisible Zipper in 10 Easy Steps
.”
Step 1:
Place and cut the left pattern piece. Keep in mind, you will need enough fabric elsewhere in your yardage to be able to cut a matching piece for the right side. Note: Trace, then cut, the pattern piece for a more accurate match.
Step 2:
Cut out the left pattern piece. Draw the seam allowance line (on the right side of the fabric) and press it under along the seam line.
Step 3:
Place the left pattern piece on your uncut fabric, paying attention to grain lines. Use the folded zipper edge to find the matching area for the right pattern piece.
Step 4:
Place the right pattern piece so the seam allowance is under the left piece and zipper seam line is matched up. Cut out the right pattern piece.
Step 5:
Draw the seam allowance line (on the right side of the fabric) and press it under along the seam line. Lay the folded zipper seam line edges together to check that both sides of the zipper seam match along the folded edge. Adjust if necessary.
Sewing the invisible zipper
Step 6:
Unzip your zipper and press the zipper tape coils open gently. Line up the edge of the left zipper teeth with the marked seam line on the left pattern piece. Glue, hand or machine baste your zipper in place between the dots marked from your pattern piece.
Step 7:
Stitch the basted zipper as close to the coils as possible using a zipper foot or an invisible zipper foot.
Zip up the zipper and press the seam gently to flatten the fold beside the zipper coils. Place the right folded edge up against the left side zipper seam. Check to make sure the left seam and folded right edges match. If not, re-press the right fold until they match.
This step took me about 5 minutes of pressing and re-pressing to get a perfect match. In the end my final fold was about 1/16" different than the original fold — about the width of the tailor's chalk seam allowance line I drew.
With the zipper still closed, use a glue stick to apply glue onto the unsewn zipper tape. Press the folded seam allowance onto the zipper tape, matching the fabric pattern across the zipper opening. This is easiest if glue basted in small increments — about 2" at a time — until the fabric is basted to the entire zipper edge. (If the glue does not hold right away or dry quickly, press it gently with a medium-heat iron to dry it faster and get a secure hold.)
Zip up the zipper, press gently to flatten the seams and check your matching pattern. It if is not close enough, remove your stitching and try again. If the zipper tape/coils are showing you may need to stitch the seam again, closer to the zipper coils.
Check your matching pattern
Enjoy your perfectly matching zipper! Now you can finish the rest of your project according to the pattern.instructions.
What is your favorite place to use an invisible zipper?
Zippers can feel super intimidating to beginner sewers, but they’re actually pretty easy to pull off, and some are easier to insert than others. Like the invisible zipper. When you add one, there’s no machine stitching visible from the right side of the project. Everything is done behind the scenes, totally concealed within the seam allowances.
When you’re working with lightweight, sheer fabrics, there’s a sense of airiness and elegance to them. Which means they deserve an equally-as-elegant finished seam that hides all your raw fabric edges. Enter the French seam.
Aprons are a lifesaver for any cook or baker, and it's easy to sew one yourself. The best thing about this project? With just a few simple measurements, you can get started — no pattern necessary.