# Making a Jig for Cutting Miters and Bevels: Part 2

Do you like to make small boxes or picture frames with mitered corners? Have you tried to cut difficult bevels on a table saw?

Earlier this week, I showed you . In this post, I’ll describe how to use the jig to make a box with mitered corners. To make things interesting, I will also join the bottom of the box to the sides with bevels. Well, bevels and miters. To establish some terms, a miter is an angled cut at the end of a board while a bevel is an angled cut on the edge of a board.

I used a jig for my table saw to cut perfect miters and bevels for this walnut box.

I’m going to make this inaugural box a rectangle. The long sides and bottom are the same length. The two short sides are squares, so their width and length are the same as the height of the long sides. For simplicity’s sake, I’m going to make my box 4” tall. I had a leftover piece of walnut a little less than ½” thick and long enough for all the parts. It had a crack, so I took that as an opportunity to make oak butterfly key inlays. (I’ll talk about those in a future post.)

## Figure continuity

I love the figure of this walnut, so I want it to continue around the box. To achieve that effect, start with a board a bit wider than 4” and long enough for all four sides and the bottom. Before crosscutting the pieces to length, mark them to preserve their positions relative to each other. While you are marking them, draw an arrow pointing upward on all the pieces except the bottom.

This will help keep them oriented while they are being cut and will also indicate the outside face of each piece. Now crosscut them (at 90 degrees) a bit longer than the final dimension so that you end up with three pieces: one piece for the bottom and two others that each contain a long side and an adjacent short side.

## Establishing the width

With the blade at 45 degrees and the jig on the table, set the table saw fence to cut the bevels on one edge of all the sides at the desired width (4” in my case). The edge of the rectangular fence should be 4” from where the board will touch the blade. The fence will not need to be adjusted again.

From here on, make sure the outside face of the pieces are facing up. Put the edge of one of the pieces against the small rectangle and move it down so that it butts against the hardwood fence. Turn the stop block on end and clamp it to the fence, making a solid place for the boards to register against. Make a cut on one long edge of all three pieces. Since the bottom needs bevels on all sides, rotate that piece 180 degrees, hold it against the jig and cut the bevel parallel to the first bevel. To avoid confusion, I mark an X on the edges that have already been cut.

Using the jig to cut a bevel on the edge of this piece of walnut

### Cutting to length

Now it’s time to cut the sides, ends and bottom to length. Remove the stop block from the jig. With the boards held against the hardwood fence, make a cut on both ends of all three pieces, remembering to keep the outside facing up. Now use the stop block to set the length for the bottom and two long side pieces. Clamp the stop block to the hardwood fence. Position the miter you’ve already cut against the stop block to cut the opposite end. After the three pieces have been cut in this manner, the bottom and two sides are finished so they can be marked and set aside.

Crosscutting miters is easy with this table saw jig.

To cut the two short sides to length, put the stop block on end in the same place as earlier. Take a long, straight piece of wood (the mitered board used to set the table saw angle works perfectly) and put it against the rectangle fence so that it butts against the hardwood fence. Position the stop block snug against the edge and clamp it in place. Put the already cut miter of the small sides against the stop block and cut them both to length. With just a few cuts, all the parts are now at their final dimensions. Before gluing them up, I like to sand the inside faces of all the parts. To control glue squeeze out (as I discussed in ), tape the inside edges of all the pieces.

## Use tape instead of clamps

For gluing up small projects with bevels and miters, I like to use painter’s tape, which provides more than enough clamping pressure and makes assembly easy. Clamps would be difficult because the miters would slide against each other. Lay out the boards with the inside faces down on a flat surface protected from glue, making sure the pieces are in the correct order for grain continuity.

Box parts arranged with continuous grain

Line the four pieces (two sides and two ends) against a straight edge such as a table saw fence. Rip off 10 or 12 pieces of tape about 2” long and have them ready to go. Touch the tips of the miters together and connect each joint with three pieces of tape. For the bottom, which should also be taped along the inside edge to avoid problems with glue, turn it with the inside facing down and apply tape perpendicular to the edge on all sides.

Box parts taped up and ready to be glued

## Wrap it up

Apply glue to the joints and on the ends, then wrap the sides together to form a rectangle. Tape the remaining joint. To attach the bottom, flip it over and apply glue to the miter and place it on the box, taping it down when everything is lined up. Check for squareness and reinforce with more tape. Once the glue dries, you’ll have a strong box. A standard miter joint is plenty strong for most applications without splines. Add keys only if you want them for decoration. Sand the outside faces, and you’re done.

Pieces of painter's tape serve as clamps to assemble this mitered box.

The great thing about this jig is that it requires so little material and comes together quickly and easily. You can make it in different sizes for different projects. As you will see, the joints will come together with no gaps. I hope you enjoy using this jig as much as I enjoyed designing it.

June 27, 2014
More to Explore
• Are you sure to want to remove this?
When it comes to popular, enduring woodworking styles in the United States, one immediately comes to mind: the Shaker. Woodworking luminaries such as George Nakashima and Wharton Esherick were influenced by the Shakers, and so are many contemporary makers like Garrett Hack, C.H. Becksvoort and Thomas Moser.
Mitch Roberson
• Are you sure to want to remove this?
For many woodworkers, Claro walnut is the connoisseur’s walnut — and it's easy to see why. Claro is a medley of subtle intermixed colors — browns, reds, black, purple, yellows — and beautiful figure.
Rob Porcaro
• Are you sure to want to remove this?
Finishing is possibly the most gratifying part of any woodworking project — and potentially the most stressful. You’ve put a lot of time and effort into what you're making, and the pressure to get the finishing touches just right can be intense.
Wilbur Pan
• Are you sure to want to remove this?
The way two pieces of wood fit together is a thing of beauty — and a great way to spot a quality piece of furniture. So nailing dovetail joints is a must when you're looking to up your woodworking game.
Rob Porcaro
• Are you sure to want to remove this?
Think about the last time you looked at a basic wooden picture frame and thought, "That thing is perfect!" Never? Yeah, probably never.
Chris Wong
• Are you sure to want to remove this?
A good woodworker knows dozens of different types of joinery. The hard part is knowing what to use, and when.
Kate Taylor
• Are you sure to want to remove this?
A while back, we looked at how a bandsaw can affect how you use and design with wood. If that didn't inspire you to buy one, this guide to choosing a bandsaw for a small woodshop should do the job.
Rob Porcaro
• Are you sure to want to remove this?
It doesn't take much time or money to make an edge grain (edge grain = just the edge strip of the wood, like the side of a 2 x 4) cutting board yourself. Plus they make awesome gifts for just about anyone old enough to be trusted with a knife.
Mitch Roberson
• Are you sure to want to remove this?
Old-world hand crafting comes naturally to Anna Warren and Sarah Kirkham, whose brand, Tactile Craftworks, is known for gorgeously embossed and tooled leather pieces. But you might be surprised to learn that digital technology is essential to everything they do and make. Working with the Dremel DigiLab digital laser-cutting tool, the pair has found a sweet spot between handcraft and high-tech — and built a successful business in the process.
• Are you sure to want to remove this?
Suddenly succulents are everywhere, and so are planters that give them a happy home. No surprise, since succulents are so easy to take care of, don’t need much water, and will grow in the tiniest of openings.
Mitch Roberson
• Are you sure to want to remove this?
Learning how to use food-safe finishes is a must for woodworkers, whether you're creating a dining table, a cutting board, or even just a decorative object. That's because many finishes contain toxic drying agents, not to mention that many people are sensitive to chemicals.
Patrick Harper
• Are you sure to want to remove this?
Handsaws: the most iconic, and yes, hardworking of the woodworking tools. But sometimes it seems like there are as many kinds of saws as there are teeth on the things. Let's narrow it down a bit to the most useful ones you'll encounter.
Rob Porcaro
• Are you sure to want to remove this?
For clean and accurate wood cuts, you've gotta have the right drilling tools. Here's a rough sketch of some items to have handy in your woodworking studio as you start tackling basic projects.
Rob Porcaro
• Are you sure to want to remove this?
Her Instagram feed is a wall of wood, tattoos, carvings and the occasional bloody finger. Her Twitter bio reads: Chainsaw artist seeking a life of travel, freedom and inspiration. When she's not working in the workshop, professional chainsaw artist Griffon Ramsey, a subject in our series Spark, is a big-time influencer who shakes up assumptions about women artists and the world of wood-carving. Her art is definitely not about happy wooden bears lingering at tourist traps — though she does have a magical story about a roadside attraction.
Lisa Shroyer
• Are you sure to want to remove this?
Typically things turned on a lathe are round because they are shaped while they rotate around a single center. While I always have enjoyed the shapes that are produced on a lathe, I also find using a single center constraining. Why limit yourself to something that is purely round when you can incorporate many circular elements in your design by using multiple sets of centers? I enjoy creating shapes that look like they were made on anything BUT a lathe. Let's have a look at one method of creating such a form.
Ed Pretty
• Are you sure to want to remove this?
Joining wood can be one of the tougher parts of creating beautiful wood creation, so we're always looking for quick and easy joinery techniques. That's exactly what makes pocket hole joinery so appealing.
Kate Taylor
• Are you sure to want to remove this?
In my last post I pointed out a few design considerations for turned forms. One primary consideration was that bowls will appear much lighter if the curve profile appeared to complete itself above, on or slightly below the surface upon which it sits. The bowl will have a lighter appearance if it does not have an overly wide base relative to the diameter of the bowl. I turn a series of forms which I call "Zen Candles" that present a problem as far as the required diameter of the base.
Ed Pretty
• Are you sure to want to remove this?
When woodworkers talk about the most important tool in their shop, often they will mention a machine, like a table saw, or a hand tool, like a plane. Either way, it’s arguable that the most important tool in any woodworker’s shop is not a hand tool or a machine, but a workbench. If you took away a woodworker’s machine or tool, the woodworker could probably figure out another way to accomplish the task at hand. But without a workbench, it becomes difficult to work on the individual pieces of a project, to assemble the piece, and to apply the finish.
Wilbur Pan
• Are you sure to want to remove this?
One of the most fun and varied items you can turn on a lathe is a lidded box. In the photo below you can see that there are several designs, usually related to how the lid fits to the box. There are an almost unlimited number of designs when creating a turned, lidded box. Not bad for such a simple little project. Lidded boxes are also a quick seller at everything from craft fairs to art galleries, so they can also be quite profitable.
Ed Pretty
• Are you sure to want to remove this?
Starting out in woodworking, as in any craft, is full of excitement, hope, and, yes, a degree of bewilderment. In the quest to put one's heart, mind and hands into making things, it helps to have some guidance. I humbly offer these tips, most of which are really applicable to all crafts.
Rob Porcaro
• Are you sure to want to remove this?
Bandsaws are terrific tools to use, and can be very versatile in cutting wood. But for a bandsaw to be at its best, it needs a sharp blade. Many problems with using a bandsaw can be traced to using a blade that is too dull for the task at hand.
Wilbur Pan